9 Simple Steps to Waterproofing Exterior Walls


“Your walls are the foundation of your house. You need to pay special attention to your house’s exterior walls because the weather out there will not be nice. It’s not enough to paint the wall. After dealing with rain, snow, wind, dust, and heat of the outside environment, the paint will start peeling off.”

Thus, waterproofing is the best way to ensure that your walls are protected and retain your house’s longevity. At the same time, it is vital to reduce your frequent renovation cost. So, here are some of the simple steps for providing effective waterproofing solutions to your home.

Damp carpets and beneath wall coverings can be the most prominent place for mold and mildew growth. Finishing a basement without first dealing with the moisture problems can make health conditions worse and lead to significant damage. Interior waterproofing systems, installed by a professional contractor, can keep the moisture away throughout the home.

Step 1: Properly expose the outside part of the wall

To start with waterproofing your exterior walls, make sure it is properly exposed to work on. Your house walls possess a lot of dirt, which creates an additional layer over the wall. Get rid of all the filth and dust from the walls. And before doing so, remove all the drainage pipes and the old field tiles to get proper access to every corner and area of the wall.

Step 2: Thoroughly clean the walls

Dust and dirt are carried by the air and stick to the outer part of the wall. To ensure the efficiency of the process, you need to clear the debris and dust thoroughly. The dirt and debris can be cleaned by using a broom, brush, or sandpaper. Then rinse it off with a power washer.

Step 3: Check out for the cracks and fill them up

Cracks and holes can develop on the exterior walls over time. Follow up the cleaning process with a thorough finding of all the cracks and holes on your wall to ensure proper weatherproofing. You can fill them with cement.

Most of the homeowners get worried about cracks in the foundation. But the fact is, not all foundation cracks affect the home’s structural integrity. Sometimes cracks can be caused by shrinkage during the concrete curing process. These unsightly, non-structural shrinkages, commonly known as hairline cracks, don’t put your home in immediate danger. But on the other hand, structural cracks are serious business.

All over the internet and TV you find websites and programs with step-by-step guides of DIY foundation repair. But the truth is that a foundation should not be experimented on in a DIY project. Foundation repair requires years of experience and specialized tools. When it comes to foundation repair, contact a foundation repair expert.

The mixture of cement penetrated inside the cracks and sealed them. Make sure to remove the loose cement from the wall before applying the cement.

Step 4: Add a layer of cement waterproofing sealer

If you want to make sure your wall is waterproof, you need to apply a cement waterproofener. After applying the cement in the crevices of the walls, let it dry and then apply the waterproof paint seal. Allow it to become wet after that.

Step 5: Pick the right water-proofer

There are many waterproof products available in the market. You need to choose the right one for the wall. Pick the water-proofer if it is a concrete wall or a silicate one.

You can choose between a silicate-based concrete seal or a concrete coating. You can add strength to your walls with a plaster waterproofing Additive.

Step 6: Apply the water-proofer

Use a roller or brush to apply the water-proofer to the walls. Give a thin coat first if you want to apply more than one layer. Add the second coating after the first one is dry.

Step 7: Apply tar and heavy-duty membrane

“If you want to add more strength to the layers, you need to use a tar-based pitch after you’ve dried the cement. It should be applied on your exterior wall.”

After that, you need to apply a heavy-duty plastic or rubber Membrane, which will ensure the proper care of your walls.

Step 8: Consider adding gravel

If you want to lay the drainage pipes, you need a proper base below the footer. The drainage pipes will be supported by a 34-inches gravel base. Gravel is long-lasting and provides enhanced protection.

You need to place the drainage pipe-cover along with the gravel. Next to the footer, level the gravel and then back-fill it. Make sure the pipe is covered for at least 3-inches.

Step 9: Add a fabric barrier

Attach the fabric barrier to the pipe. The formation of dirt is prevented by a fabric barrier. Then build the top of the dirt relatively high and let it settle for some time. Slope the ground away from the walls for the run-off after youTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkiaTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia isTrademarkia is


Good waterproof gives your home a new life and strength to deal with weather-related issues. If you want good solutions for your walls, Magicrete is here to help you. At a very low and affordable price, Magicrete offers you proper weatherproofing.

“It’s not like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it’s like it”

Leave a Reply

Your email address will not be published. Required fields are marked *